FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   + 3.2. Engine DOHC
   - 3.3. Engine V6
      3.3.1. A technical characteristics
      3.3.2. The repair which is not demanding removal of the engine
      3.3.3. Engine removal
      - 3.3.4. Dismantling and check of details of the engine
         3.3.4.1. Engine dismantling
         3.3.4.2. Check of degree of deterioration of details of the engine
         3.3.4.3. Axis knot коромысел
         3.3.4.4. Pushers of valves and a bar of pushers
         3.3.4.5. A camshaft
         3.3.4.6. Heads of the block of cylinders
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and piston rings
         3.3.4.9. Piston fingers and rods
         3.3.4.10. A cranked shaft
         3.3.4.11. Radical and шатунные bearings
         3.3.4.12. Distributive gear wheels
         3.3.4.13. A flywheel
         + 3.3.4.14. Greasing system
         3.3.4.15. Ventilation system картера
         - 3.3.4.16. Engine assemblage
            3.3.4.16.1. Installation of a cranked shaft
            3.3.4.16.2. Camshaft installation
            3.3.4.16.3. Installation of pistons and rods
            3.3.4.16.4. Installation of the oil pump
            3.3.4.16.5. Flywheel installation
            3.3.4.16.6. Installation of a gear wheel and a cover of a drive of the distributive mechanism
            3.3.4.16.7. Installation of the oil pallet, the water pump and a pulley коленвала
            3.3.4.16.8. Removal and installation of the oil heat exchanger
            3.3.4.16.9. Heads of the block of cylinders, axes коромысел and an inlet collector
         3.3.4.17. Adjustment of backlashes of valves
         3.3.4.18. Auxiliary details of the engine
         3.3.4.19. Engine installation
         3.3.4.20. Start of the engine after major repairs or restoration
      + 3.3.5. Changes in a design of engines V6 2,4 and 2,9 дм3
   + 3.4. Ignition and engine management systems
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment



3.3.4.16.9. Heads of the block of cylinders, axes коромысел and an inlet collector
THE GENERAL DATA

Linings of a head of the block of cylinders and marks

Sequence of a tightening of bolts of fastening of a head of the block of cylinders

Sequence of a tightening of bolts of fastening of an inlet collector


PERFORMANCE ORDER
1. To grease pushers of valves with pure engine oil and to insert them into the block of cylinders. To watch that they were established on former places.
2. To check up that interfaced surfaces of the block of cylinders and heads of the block of cylinders owe the pure.
3. To establish new linings of heads of the block of cylinders on directing plugs on the block of cylinders. To watch a correct arrangement of linings. The left and right linings differ from each other. On linings there is an inscription "FRONT TORAHS" ("the forward top party").
4. Cautiously to lower heads of the block of cylinders on the block of cylinders and to fix bolts.
5. In three steps, in certain sequence to tighten bolts according to the moments of an inhaling specified in subsection 3.3.1.
6. To grease bars of pushers with engine oil and to insert them into the block of cylinders.
7. To establish on heads of the block of cylinders маслоотражательные guards and to establish axes клапанных коромысел in gathering.
8. To insert adjusting screws of levers of valves into nests of bars of pushers.
9. Gradually to tighten fixing bolts of axes клапанных коромысел till the corresponding moment of an inhaling.
10. To grease external edge of a contact surface of heads of the block of cylinders and a contact surface of an inlet collector with hermetic for lining installation.
11. To establish into place a new lining of an inlet collector and to establish an inlet collector.
12. To establish fixing bolts of an inlet collector and to tighten them in four receptions till the necessary moment of an inhaling in certain sequence.
13. To adjust клапанные backlashes.