FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   + 3.2. Engine DOHC
   + 3.3. Engine V6
   - 3.4. Ignition and engine management systems
      3.4.1. A technical characteristics
      - 3.4.2. Ignition and engine management systems
         3.4.2.1. System of ignition ESC II
         3.4.2.2. System of ignition ЕЕС IV
         3.4.2.3. The ignition distributor
         3.4.2.4. Check of a corner of installation of an advancing of ignition
         3.4.2.5. The ignition block (models with system of injection of fuel)
         3.4.2.6. The ignition coil
         3.4.2.7. A fuel trap on engines with the carburettor
         3.4.2.8. The engine management block
         3.4.2.9. The step-by-step engine of the carburettor
         3.4.2.10. The device of heating of an inlet collector of engines with the carburettor
         3.4.2.11. The relay of a control system of the engine
         3.4.2.12. Installation of a corner of an advancing of ignition and idling turns
         3.4.2.13. The gauge of turns and position of a cranked shaft
         3.4.2.14. The gauge of temperature of air
         3.4.2.15. The gauge of temperature of fuel
         3.4.2.16. The gauge of speed of the car
         3.4.2.17. The gauge of absolute pressure in a collector (MAP)
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment



3.4.2.4. Check of a corner of installation of an advancing of ignition
THE GENERAL DATA

ALL ENGINES, EXCEPT DOHC

Scales of installation of the moment of ignition of engine OHC


Scale of installation of the moment of ignition and engine V6 label

1 – a scale of installation of the moment of ignition,

2 – a pulley with a label

Installation of a corner an ignition advancing is established very precisely at car manufacturing. Adjustment is necessary after removal of the distributor of ignition or a gear belt of a drive.

Before check it is necessary to satisfy following conditions:

  – The engine should be heated-up;
  – On engines with the carburettor, the vacuum pipe should be disconnected from a collector and a collector aperture is muffled by a stopper;
  – Idling turns should be below 900 rpm;
  – To disconnect and isolate a wire of the oktan-proof-reader.

PERFORMANCE ORDER
1. To clear adjusting labels. On engines OHC the scale of installation of the moment of ignition (1) is on a pulley of a cranked shaft, and the index (2) on a cover should be combined with a corresponding label on a pulley.

The prevention

Two alternative types of a pulley with different labels are applied. On engines V6 there is one cut on a pulley, and the scale of installation of the moment of ignition is on a cover.


3. To connect a stroboscope to a high-voltage wire of 1 cylinder and further according to the maintenance instruction.
4. To start the engine in a mode of idling and to direct light from a stroboscope on labels. Labels should be on a place and be combined with the index on demanded coal of installation of ignition.
5. For adjustment of the moment of ignition to stop the engine, to weaken a bolt of fastening of the distributor of ignition, to turn the distributor and to tighten a fastening bolt. For an ignition advancing to turn the distributor counter-clockwise and on the contrary. To start the engine and repeatedly to check up adjustment of the moment of ignition.

ENGINE DOHC

Installation of a corner of an advancing of ignition is made by block ESC II or ЕЕС IV, and no additional regulation is possible.