FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   + 3.2. Engine DOHC
   + 3.3. Engine V6
   - 3.4. Ignition and engine management systems
      3.4.1. A technical characteristics
      - 3.4.2. Ignition and engine management systems
         3.4.2.1. System of ignition ESC II
         3.4.2.2. System of ignition ЕЕС IV
         3.4.2.3. The ignition distributor
         3.4.2.4. Check of a corner of installation of an advancing of ignition
         3.4.2.5. The ignition block (models with system of injection of fuel)
         3.4.2.6. The ignition coil
         3.4.2.7. A fuel trap on engines with the carburettor
         3.4.2.8. The engine management block
         3.4.2.9. The step-by-step engine of the carburettor
         3.4.2.10. The device of heating of an inlet collector of engines with the carburettor
         3.4.2.11. The relay of a control system of the engine
         3.4.2.12. Installation of a corner of an advancing of ignition and idling turns
         3.4.2.13. The gauge of turns and position of a cranked shaft
         3.4.2.14. The gauge of temperature of air
         3.4.2.15. The gauge of temperature of fuel
         3.4.2.16. The gauge of speed of the car
         3.4.2.17. The gauge of absolute pressure in a collector (MAP)
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment



3.4.2.3. The ignition distributor
THE GENERAL DATA

The distributor of ignition of engine OHC

1 – a cover,

2 – a rotor of the distributor,

3 – the distributor of ignition,

4 – a sealing ring,

5 – a socket

The distributor of ignition of engine DOHC

1 – tips of high-voltage wires,
2 – the screw of fastening of a cover,
3 – a cover,
4 – a rotor of the distributor,
5 – a bolt,
6 – a distributor drive

High-voltage wires and engine DOHC spark plugs

1 – a spark plug,

2 – a tip,

3 – high-voltage wires,

4 – holders of high-voltage wires

Position of a rotor of the distributor before and after removal

 

ALL ENGINES, EXCEPT V6 2,4 and 2,9 дм3


The prevention

The ignition distributor should not act in film without the serious reason as accuracy of installation of a corner the ignition advancing, reached in manufacture hardly can be restored.


PERFORMANCE ORDER
1. To remove a negative wire from the accumulator.
2. To uncover the distributor.
3. Using a key, for a bolt of a pulley of a cranked shaft, to turn the engine before installation of the piston of 1 cylinder in an ignition point, that is when:
     – Adjusting labels are in combination position;
     – The distributor rotor is combined with contact of a high-voltage wire of 1 cylinder.
4. When the cylinder is in ignition position, the rotor should be combined with a groove on the distributor case.
5. To wring out a blocking clip on многовыводном a socket of the distributor and to disconnect a socket.
6. To put combination labels on the distributor and the engine, then to unscrew a bolt of fastening of the distributor and a tightening lath. On engines V6 because of the limited access it is necessary to use a special key. If it is established supporting скоба, to unscrew it.
7. To remove the ignition distributor, having noted new position of a rotor of the distributor. As spare parts to the distributor (2) the rotor of the distributor and a sealing ring of round section (1) are delivered.
8. At installation of the distributor of ignition to establish a rotor in position in which it was after removal, that is it should be turned on 20 clockwise from the moment of ignition of 1 cylinder.
9. To establish the ignition distributor on the engine, thus a distributor rotor should turn counter-clockwise and be established in position in which it was before removal, otherwise to repeat installation. Correct installation of the distributor of ignition is defined on combination of a label (1) on a rotor with a ledge (2) on the distributor case. For exact combination of a label and a ledge it is necessary to turn the distributor case in one or other party.
10. To establish a tightening lath and to fix the distributor a bolt.
11. The further installation is made in sequence, return to removal.

ENGINES V6 2,4 And 2,9 дм3

The prevention

The ignition distributor should not act in film without the serious reason as accuracy of installation of a corner the ignition advancing can be reached only with use of the special equipment.


Position of a rotor before installation on engine V6 2,4 and 2,9 дм3

With – a label on the case

PERFORMANCE ORDER
1. To remove a negative wire from the accumulator.
2. To remove high-voltage wires from spark plugs.
3. To uncover the distributor of ignition and to move it aside together with wires.
4. To turn the engine for a fastening bolt гасителя крутильных fluctuations in a point of installation of the piston of 1 cylinder at the moment of ignition (12 to the top dead point), having combined a label on a pulley of a cranked shaft (1) with division 12 on a scale of installation of the moment of ignition (2).
5. In the absence of a label on a pulley of a cranked shaft to put combination labels further precisely to establish a distributor rotor.
6. To note position of a plate of installation of the distributor of ignition concerning the block of cylinders.
7. To disconnect a socket from the ignition distributor.
8. To unscrew a bolt (1) fastenings and to remove the distributor of ignition (2).
9. To establish the ignition distributor so that installation labels were combined.
10. After distributor installation, rotating the distributor case to combine contact of a rotor to a label With on the case (fig. Position of a rotor before installation on engine V6 2,4 and 2,9 дм3 see) and to fix the distributor in this position by a bolt.
11. The further installation is made in sequence, return to removal.
12. To warm up the engine and to check up installation of a corner of an advancing of ignition.