накрутка голосов в голосовании в контакте

FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   - 3.1. Engine OHC
      3.1.1. A technical characteristics
      - 3.1.2. Service and repair
         3.1.2.1. Engine adjustment
         - 3.1.2.2. The repair which is not demanding removal of the engine
            3.1.2.2.1. Removal and installation of a gear belt
            3.1.2.2.2. Removal of a head of the block of cylinders
            3.1.2.2.3. Dismantling and assemblage of a head of the block of cylinders
            3.1.2.2.4. Installation of a head of the block of cylinders
            3.1.2.2.5. Removal and installation of the oil pallet
            3.1.2.2.6. Replacement of a forward sealing ring of a cranked shaft
            3.1.2.2.7. Replacement of a back sealing ring of a cranked shaft
            3.1.2.2.8. Replacement of support of the engine
         3.1.2.3. Removal and engine installation
         + 3.1.2.4. Engine repair
         3.1.2.5. Greasing system
         3.1.2.6. Ventilation system картера
   + 3.2. Engine DOHC
   + 3.3. Engine V6
   + 3.4. Ignition and engine management systems
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment



3.1.2.2.4. Installation of a head of the block of cylinders
THE GENERAL DATA

Order of a tightening of bolts of fastening of a head of the block of cylinders

Packing of a lining of a cover of a head of the block of cylinders


PERFORMANCE ORDER
1. To clear surfaces прилегания linings on the top plane of the block of cylinders and the bottom plane of a head of the block of cylinders.
2. To screw up in the block of cylinders adjusting pins (the adaptation 21.003) and to establish a new lining of a head of the block of cylinders (fig. Packing of a lining of a cover of a head of the block of cylinders see).
3. To establish a head of the block of cylinders. To screw in in accessible apertures a hand its bolts, to replace adjusting pins with other bolts of fastening of a head of the block of cylinders.
4. To tighten bolts of a head of the block of cylinders (the adaptation 21.002) in the three first stage, observing a corresponding order of their tightening (fig. the Order of a tightening of bolts of fastening of a head of the block of cylinders see).
5. To establish according to adjusting signs pulleys on cranked and distributive shaft.
6. To establish the ignition distributor, a gear belt and to unblock the tension device of a gear belt.

The prevention

After installation of a gear belt it is possible to rotate a cranked shaft exclusively in a direction in which the shaft rotates at engine work.


7. To establish a cover of a head of the block of cylinders and to tighten bolts according to recommended order (fig. the Order of a tightening of bolts of a cover of a head of the block of cylinders see).
8. To screw up spark plugs, to screw a casing of a gear belt and to attach a reception exhaust pipe to a final collector.
9. To establish on the distributor of ignition the distributor of a high voltage and to attach high voltage wires to corresponding spark plugs.
10. To connect a vacuum hose to the carburettor, and also pipelines of giving and tap of a cooling liquid to the case of the automatic starting arrangement of the carburettor.
11. To connect the pipeline of ventilation of a transmission to an oil separator.
12. To connect the pipeline of the vacuum amplifier of brakes and a cable of a pedal of an accelerator.
13. To connect hoses: top and bottom to a broad tank and to fill system of cooling with a liquid to corresponding level.
14. To connect to the accumulator a wire of weight of the car and to establish the bottom casing.
15. To start the engine and to warm up it to working temperature.
16. To adjust a corner of an advancing of ignition, number of turns of idling and concentration WITH in exhaust gases.
17. After engine warming up to uncover heads of the block of cylinders and to disconnect wires of a high voltage from spark plugs.
18. To tighten bolts of a head of the block of cylinders (the adaptation 21.002) on an order resulted on fig. the Order of a tightening of bolts of fastening of a head of the block of cylinders.
19. To establish a cover of a head of the block of cylinders, observing during a tightening corresponding sequence (fig. the Order of a tightening of bolts of a cover of a head of the block of cylinders see) and to connect high voltage wires to spark plugs.
20. To establish the air filter.