FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
- 5. Fuel system
   5.1. A technical characteristics
   5.2. Fuel
   5.3. Neetilirovannyj gasoline of engines V6, 2.4 and 2.9 дм3
   + 5.4. System of giving of air
   + 5.5. Carburettor PIERBURG
   + 5.6. Carburettor WEBER 2V
   + 5.7. Carburettor WEBER 2V TLD
   - 5.8. System of injection of fuel
      5.8.1. Adjustment of turns of idling and quality of a mix
      5.8.2. Removal and installation of the gauge of position throttle заслонки
      5.8.3. Removal and installation of the valve of management by idling turns
      5.8.4. Removal and installation of measuring instruments of a stream of air
      5.8.5. Removal and installation of fuel atomizers
      5.8.6. Removal and installation of the temperature gauge of a fuel highway
      5.8.7. Removal and installation of a regulator of pressure of fuel
      5.8.8. Removal and installation of the case throttle заслонки on engine DOHC
      5.8.9. Removal and installation of the oxygen gauge (HEGO)
      5.8.10. Removal and installation of a coal adsorber
      5.8.11. Removal and installation of the electromagnetic valve of a coal adsorber
   5.9. Removal and installation of an inlet collector
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


5.8.7. Removal and installation of a regulator of pressure of fuel
THE GENERAL DATA

Regulator of pressure of fuel

1 – a vacuum branch pipe,

2 – the top case,

3 – a spring,

4 – a diaphragm,

5 – the valve,

6 – the bottom case,

7 – a flange,

8 – a lining

PERFORMANCE ORDER
Engine OHC and V6 2,8 дм3
1. To remove a wire of weight from the accumulator.
2. On engines V6 to disconnect high-voltage wires from скобы a regulator of pressure of fuel.
3. To establish under a regulator of pressure of fuel the corresponding container and to disconnect a returnable fuel tube (it is specified by an arrow).
4. To disconnect from a regulator a vacuum tube (it is specified by an arrow).
5. To weaken a nut муфты givings of fuel and to remove pressure in fuel system.
6. To unscrew a nut (it is specified by an arrow) from the basis of a regulator and to remove a regulator.
7. Installation is made in sequence, return to removal.
Engine DOHC
8. To remove a wire of weight from the accumulator.
9. Slowly to weaken connection of giving of fuel of a fuel distributive highway, to remove pressure in fuel system.
10. To disconnect a hose of return of fuel (it is specified by an arrow) from a pressure regulator.
11. To disconnect a vacuum tube from the top part of a regulator.
12. To unscrew two fixing bolts and to take a regulator from a fuel highway together with a sealing ring.
13. To establish a new sealing ring on a regulator, preliminary having greased with its engine oil.
14. The further installation is spent to sequences, return to removal.
Engines V6, 2,4 and 2,9 дм3
15. To remove a wire of weight from the accumulator.
16. Slowly to weaken connection of giving of fuel of a fuel distributive highway, to remove pressure in fuel system.
17. On engines with an aluminium fuel distributive highway and a regulator of pressure of fuel of late model to remove from regulator top keeping collar of a tube of return of fuel.
18. To establish under a regulator of pressure of fuel the corresponding container and to disconnect a returnable fuel hose (it is specified by an arrow) and a vacuum tube from a regulator of pressure of fuel.
19. To unscrew and remove from a fuel highway a regulator.
20. Installation is made in sequence, return to removal. A sealing ring to grease with silicone greasing. To include 5 times ignition, not including an engine starter, to lift pressure in fuel system.