FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
- 5. Fuel system
   5.1. A technical characteristics
   5.2. Fuel
   5.3. Neetilirovannyj gasoline of engines V6, 2.4 and 2.9 дм3
   + 5.4. System of giving of air
   + 5.5. Carburettor PIERBURG
   + 5.6. Carburettor WEBER 2V
   + 5.7. Carburettor WEBER 2V TLD
   - 5.8. System of injection of fuel
      5.8.1. Adjustment of turns of idling and quality of a mix
      5.8.2. Removal and installation of the gauge of position throttle заслонки
      5.8.3. Removal and installation of the valve of management by idling turns
      5.8.4. Removal and installation of measuring instruments of a stream of air
      5.8.5. Removal and installation of fuel atomizers
      5.8.6. Removal and installation of the temperature gauge of a fuel highway
      5.8.7. Removal and installation of a regulator of pressure of fuel
      5.8.8. Removal and installation of the case throttle заслонки on engine DOHC
      5.8.9. Removal and installation of the oxygen gauge (HEGO)
      5.8.10. Removal and installation of a coal adsorber
      5.8.11. Removal and installation of the electromagnetic valve of a coal adsorber
   5.9. Removal and installation of an inlet collector
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment



5.8.3. Removal and installation of the valve of management by idling turns
THE GENERAL DATA

The valve of management of turns of idling of engine DOHC

The valve of management of idling turns is specified by an arrow.

PERFORMANCE ORDER
Engines OHC and V6
1. To remove a wire of weight from the accumulator.
2. To remove a socket (it is specified by an arrow) from the management valve, having unbent keeping clip.
3. To unscrew two nuts of fastening (ОНС) (or a bolt on engine V6) and to take the valve (it is specified by an arrow).
4. If necessary to unscrew two screws and to remove the coil from the valve.
5. To establish into place the valve, using a new lining, to tighten nuts or bolts.
6. To connect a socket and a wire of weight of the accumulator.
7. To start the engine and to check up stability of idling.
8. To warm up the engine to working temperature, to include all electric consumers and to check up that idling turns remained stable.
Engine DOHC
9. To remove a wire of weight from the accumulator.
10. To weaken a collar and to disconnect from a throttle воздухозаборный a hose.
11. To unscrew a nut of fastening and to disconnect воздухозаборную a tube from скобы on the forward panel of a motor compartment.
12. To remove a socket from the management valve, having unbent keeping clip.
13. To disconnect clips of a cover of the air filter, to remove воздухозаборную a tube, the chamber of superfluous pressure and a cover of the air filter as one assemblage, having disconnected a ventilation hose картера from воздухозаборной tubes.
14. To unscrew two bolts of fastening and to take the valve from воздухозаборной tubes.
15. Installation is made in sequence, return to removal.
16. To start the engine and to check up stability of idling.
17. To warm up the engine to working temperature, to include all electric consumers and to check up that idling turns remained stable.