FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
- 5. Fuel system
   5.1. A technical characteristics
   5.2. Fuel
   5.3. Neetilirovannyj gasoline of engines V6, 2.4 and 2.9 дм3
   + 5.4. System of giving of air
   + 5.5. Carburettor PIERBURG
   + 5.6. Carburettor WEBER 2V
   + 5.7. Carburettor WEBER 2V TLD
   - 5.8. System of injection of fuel
      5.8.1. Adjustment of turns of idling and quality of a mix
      5.8.2. Removal and installation of the gauge of position throttle заслонки
      5.8.3. Removal and installation of the valve of management by idling turns
      5.8.4. Removal and installation of measuring instruments of a stream of air
      5.8.5. Removal and installation of fuel atomizers
      5.8.6. Removal and installation of the temperature gauge of a fuel highway
      5.8.7. Removal and installation of a regulator of pressure of fuel
      5.8.8. Removal and installation of the case throttle заслонки on engine DOHC
      5.8.9. Removal and installation of the oxygen gauge (HEGO)
      5.8.10. Removal and installation of a coal adsorber
      5.8.11. Removal and installation of the electromagnetic valve of a coal adsorber
   5.9. Removal and installation of an inlet collector
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment



5.8.5. Removal and installation of fuel atomizers
THE GENERAL DATA

Fuel atomizer

1 – a sealing ring,

2 – the entrance filter,

3 – an anchor,

4 – a winding of the coil,

5 – the case,

6 – a sealing ring,

7 – the needle valve,

8 – a needle of an atomizer,

9 – electric contact

Fuel highway and atomizers


Arrangement of bolts of fastening of a fuel highway on engine V6

Bolts of fastening of a fuel highway are specified by arrows.

Removal of a fuel atomizer from a highway

1 – a keeping clip,

2 – a fuel highway,

3 – a fuel atomizer

Fuel atomizer with the removed sealants

1 – a fuel atomizer,

2 – уплотнители


The union of giving of fuel on a fuel highway

The union of giving of fuel is specified by an arrow.


PERFORMANCE ORDER
Engines OHC and V6 2,8 дм3
1. To remove a wire of weight from the accumulator.
2. On engines V6 to uncover connections of a throttle which fastens three screws.
3. To remove a highway connecting a measuring instrument of a stream of air with the inlet pipeline.
4. On engines ONS to uncover the distributor and to place it aside. If necessary to remove high-voltage wires.
5. To remove a socket from the valve of turns of idling, the gauge of position throttle заслонки and the gauge of temperature of a cooling liquid.
6. On engines V6 to disconnect a cable of a throttle from скобы a regulator of fuel pressure.
7. Slowly to disconnect vacuum and fuel tubes from a regulator of fuel pressure and connection of giving of fuel from a fuel highway.
8. To remove the chamber of superfluous pressure and the throttle case.
9. To disconnect wires of fuel atomizers.
10. To unscrew a fuel arm and to remove it together with fuel atomizers.
11. Sealing rings and keeping clips on all fuel atomizers are subject to replacement even if only one fuel atomizer is necessary for taking out from a highway. The bottom sealing ring is established between thick and thin washers on the atomizer end.
12. Installation is made in sequence, return to removal. Sealing rings to grease with silicone greasing Ford-ESEM 1С171А. To check up the maintenance WITH.
Engines DOHC
13. To remove a wire of weight from the accumulator.
14. For access improvement to remove a socket from the gauge of temperature of arriving air, a wire of a high voltage and a cable of an accelerator or to move them aside.
15. Slowly to weaken connection of giving of fuel to a highway for pressure removal in fuel system and to disconnect a hose.
16. To remove a returnable fuel hose (it is specified by an arrow) from a highway.
17. To remove a vacuum tube from the top part of a regulator of pressure.
18. To remove sockets from fuel atomizers and the temperature gauge.
19. To unscrew two bolts of fastening and to remove a fuel highway.
20. To take fuel atomizers from a head of the block of cylinders.
21. Sealing rings and keeping clips on all fuel atomizers are subject to replacement even if only one fuel atomizer is necessary for taking out from a highway. The bottom sealing ring is established between thick and thin washers on the atomizer end.
22. Installation is made in sequence, return to removal. Sealing rings to grease with silicone greasing Ford-ESEM 1С171А. To check up the maintenance WITH.
Engines V6, 2,4 and 2,9 дм3
23. To remove a wire of weight from the accumulator.
24. To remove a highway connecting a measuring instrument of a stream of air with the inlet pipeline.
25. To disconnect the lever of communication from the case of a throttle and to unscrew 2 bolts of fastening скобы a throttle cable.
26. To disconnect from the throttle case vacuum tubes, the ventilation valve картера and a regulator of pressure of fuel.
27. To disconnect sockets from the gauge of position throttle заслонки, gauges of temperature of the engine and a cooling liquid and the valve of management of idling turns.
28. To unscrew 6 bolts of "Togh", which крепят воздухозаборную the chamber.
29. Slowly to weaken connection of giving of fuel of a fuel distributive highway, to remove pressure in fuel system.
30. To disconnect a tube of giving of fuel of a fuel highway and a tube of return of fuel.
31. To unscrew bolts of fastening of a fuel highway and to remove a highway.
32. To remove fixing clips and to take from a highway fuel atomizers.
33. Sealing rings and keeping clips on all fuel atomizers are subject to replacement even if only one fuel atomizer is necessary for taking out from a highway. The bottom sealing ring is established between thick and thin washers on the atomizer end.
34. Installation is made in sequence, return to removal. Sealing rings to grease with silicone greasing Ford - ESEM 1С171А. To check up the maintenance WITH.
35. On engines with a regulator of pressure of fuel of early release if it is necessary to connect to a highway a new entrance fuel tube. The new connector is delivered with a control fascinating ring and allows to keep a connector teeth taken away. When two halves of a connector are compressed together, the ring jumps out that testifies that connection has passed successfully.
36. To include 5 times ignition, not including an engine starter, to lift pressure in fuel system.