FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
- 14. An electric equipment
   14.1. A technical characteristics
   14.2. Safety locks and the relay
   14.3. Electronic blocks of management
   14.4. System of the central blocking
   14.5. System of indexes of turns
   14.6. The fuel computer
   14.7. Additional control system
   + 14.8. The generator
   + 14.9. A starter
   + 14.10. A windscreen screen wiper, knot of indexes and a headlight
   14.11. Removal and installation of a combination of devices
   14.12. External and internal illumination
   - 14.13. An other electric equipment
      14.13.1. Removal and installation of switches, engines and gauges
      14.13.2. Additional control system
      14.13.3. Removal and radio receiver installation
      14.13.4. Removal and installation of loudspeakers
      14.13.5. System of the anticreeping alarm system
   + 14.14. Electroschemes



14.13.2. Additional control system

LAMPS OF THE GRAPHIC DISPLAY

PERFORMANCE ORDER
1. To remove a combination of devices.
2. To remove from a combination of devices the graphic display.
3. Lamps and light-emitting diodes can be removed from the block of the graphic display tweezers. At replacement of a light-emitting diode of the alarm system of a jellied mouth of fuel pay attention that the label on a light-emitting diode should be combined with a yellow speck on the panel.

THE GAUGE OF THE JELLIED MOUTH OF FUEL

The gauge of a jellied mouth of fuel

The gauge is specified by an arrow.

PERFORMANCE ORDER
1. To open a cover of a jellied mouth of fuel and to remove a mouth stopper.
2. In a luggage compartment to remove on the right side an upholstery and to disconnect a gauge socket.
3. To unscrew the screw of fastening of the gauge to a mouth neck.
4. To remove the gauge.
5. Gauge installation is made in sequence, return to removal.

THE GAUGE OF TEMPERATURE OF EXTERNAL AIR

The gauge is located under a forward bumper.

PERFORMANCE ORDER
1. To disconnect an electric socket from the gauge.
2. To drown in the gauge fixing clips and to take the gauge (it is specified by an arrow).
3. At installation at first to connect a socket, then to insert a hook on the gauge end into a cut and to press the gauge into place, then to fix a socket in a clip.

THE DOOR SWITCH

PERFORMANCE ORDER
1. To remove an internal upholstery of a door.
2. To pull the switch outside for its liberation from the lock and to disconnect a socket.
3. Installation of the door switch is made in sequence, return to removal.

THE GAUGE OF LEVEL OF THE COOLING LIQUID

The gauge of level of a cooling liquid

 

PERFORMANCE ORDER
1. To uncover a broad tank.
2. To merge cooling liquid from a tank so that the gauge has appeared above liquid level.
3. To disconnect an electric socket.
4. To unscrew a fixing ring and to take the gauge from a nest, thus to note an arrangement of facets on consolidation and the gauge.
5. Gauge installation is made in sequence, return to removal.

THE GAUGE OF LEVEL OF THE LIQUID IN THE WASHER TANK

The gauge of level of a liquid in a washer tank


PERFORMANCE ORDER
1. To merge a liquid from a tank so that the gauge has appeared above liquid level.
2. To disconnect an electric socket.
3. Being careful to pick up the gauge and to take it from consolidation, thus to note an arrangement of facets on consolidation and the gauge.
4. Gauge installation is made in sequence, return to removal.

THE BLOCK OF ADDITIONAL CONTROL SYSTEM

PERFORMANCE ORDER
1. To remove a combination of devices and the top part of the panel.
Models till April, 1992
2. To unscrew two screws (are specified by arrows) block fastenings, to disconnect a socket, preliminary having wrung out a lock clip, and to remove the block.
3. Installation is made in sequence, return to removal.
4. Before panel installation to check up working capacity of additional control system.
Models since April, 1992
5. To remove furnish from the lever of opening of a cowl for access to fastening screws.
6. To unscrew three screws and to remove the lever.
7. To disconnect скобы fastenings of a cable of opening of a cowl and to disconnect a cable from the lever.
8. To unscrew five screws of fastening of the bottom furnish пенели devices and to remove it.
9. To unscrew the screw of fastening of the block, to remove from the block a socket and to take the block (it is specified by an arrow) from the car.
10. Installation is made in sequence, return to removal.

THE BLOCK OF THE CONTROL OF WORKING CAPACITY OF LAMPS

The block of the control of working capacity of lamps накаливания

The block is specified by an arrow.

On models since April, 1992 the block of the control of working capacity of lamps накаливания is located on the right over pedals.

PERFORMANCE ORDER
Models till April, 1992
1. To remove furnish under the panel of devices from outside the driver which fastens six screws one of which is accessible only after removal of a lattice of the fan.
2. To take the block from an arm, to disconnect a socket, preliminary having wrung out a lock clip, and to remove the block.
3. Installation is made in sequence, return to removal.
Models since April, 1992
4. To remove furnish under the panel of devices from outside the driver.
5. To take the block from an arm, to disconnect a socket, preliminary having wrung out a lock clip, and to remove the block.
6. Installation is made in sequence, return to removal.

THE SWITCH OF THE CONTROL SYSTEM IN THE SPEED OF THE CAR

PERFORMANCE ORDER
1. To remove a steering wheel.
2. To unscrew three screws of fastening contact скобы a sound signal.
3. To disconnect wires and to remove скобу.
4. Cautiously to take the switch from a steering wheel.

THE VACUUM VALVE / THE SWITCH

The switch of a pedal of coupling is established in a spring to a suspension bracket to compensate insignificant deviations of position of a pedal at work of the self-regulated mechanism.

PERFORMANCE ORDER
1. To remove furnish under the panel of devices from outside the driver.
2. On a brake pedal to weaken the top switch and a nut of the bottom fastening, then to unscrew a nut completely.
3. To disconnect contact of a wire and a vacuum hose from the valve, to remove the valve.
4. To disconnect contact of a wire and a vacuum hose, then to take the switch of a pedal of coupling from a suspension bracket.
5. Installation is made in sequence, return to removal.
6. To adjust switch position so that there was interval Х = at least 1,5 mm between a head of a rod of the switch and the switch case.

THE VACUUM PUMP

The vacuum pump is located behind the left headlight on models with the carburettor and behind the right headlight on all models with injection system.

PERFORMANCE ORDER
1. To remove a corresponding headlight.
2. To disconnect многовыводной the tip and a vacuum hose from the pump.
3. By means of the lever to release three support and to take the pump.
4. At pump installation into place to insert support of the pump flat-nose pliers.
5. To connect a vacuum hose and многовыводной a socket, then to establish a headlight.

VACUUM DRIVE

PERFORMANCE ORDER
1. To disconnect one end of a cable “a vacuum drive-throttle”.
2. To disconnect a vacuum hose from a drive.
3. To unscrew a lock nut of a drive and to take a vacuum drive from a suspension bracket.
4. Installation is made in sequence, return to removal.
5. On all models, except the carburettor 2,0 дм3 to adjust a cable so that it slightly sagged in the position of a throttle corresponding to idling.
6. On all models, except the carburettor 2,0 дм3 to adjust a cable so that it slightly sagged in the position of a throttle corresponding to idling.
7. To observe for плунжером the step-by-step engine. To include ignition for some seconds, then to switch off it again. When ignition is switched off, плунжер should be in position "completely openly", that is will involve inside.
8. After retraction плунжера to disconnect a wire of weight from the accumulator.
9. To adjust a cable of a vacuum drive so that it slightly sagged, then to connect a weight wire to the accumulator.

THE PRINTED-CIRCUIT BOARD

The printed-circuit board is located in a steering wheel and can be removed after branch of a contact plate of a sound signal and separation of conclusions of the switch.

THE ENGINE OF THE FAN OF THE HEATER

PERFORMANCE ORDER
1. To remove a negative wire from the accumulator.
2. To remove rubber consolidation (it is specified by an arrow) from the top part of a partition of a motor compartment.
3. To remove from a forward part of a partition two скобы fastenings of wires (marksman).
4. To unscrew two screws and to remove two скобы, which крепят a cover of the chamber (arrow). To Uncover.
5. To disconnect многовыводной a socket from the resistor of the engine of the fan and the earthen tyre.
6. To unscrew two bolts of fastening of the engine of the fan of a heater. To remove the engine together with a casing and the resistor.
7. To remove clips of fastening of half of casing of the fan and to take the engine.
8. Installation is made in sequence, return to removal. To attach wires (are specified by arrows) connections of the engine of the fan.