FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
+ 3. Engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
- 14. An electric equipment
   14.1. A technical characteristics
   14.2. Safety locks and the relay
   14.3. Electronic blocks of management
   14.4. System of the central blocking
   14.5. System of indexes of turns
   14.6. The fuel computer
   14.7. Additional control system
   + 14.8. The generator
   + 14.9. A starter
   + 14.10. A windscreen screen wiper, knot of indexes and a headlight
   14.11. Removal and installation of a combination of devices
   14.12. External and internal illumination
   - 14.13. An other electric equipment
      14.13.1. Removal and installation of switches, engines and gauges
      14.13.2. Additional control system
      14.13.3. Removal and radio receiver installation
      14.13.4. Removal and installation of loudspeakers
      14.13.5. System of the anticreeping alarm system
   + 14.14. Electroschemes


14.13. An other electric equipment

Replacement of the engine of the proof-reader of light of headlights

The engine of the proof-reader of light of headlights is established from the back party of a headlight and fastens with the help байонетного a clip.

PERFORMANCE ORDER
1. To remove an electric socket from the engine of the proof-reader of light of headlights.
2. To press the engine of the proof-reader in a direction of a headlight and in this position to turn the engine clockwise for the right headlight or counter-clockwise for the left headlight.
3. Through an aperture in the headlight case to press the lever of a fixing adjusting shaft and to take the engine of the proof-reader from a headlight.
4. Installation is made in sequence, return to removal.

Removal and installation of hours

PERFORMANCE ORDER
1. To remove the top console.
2. For removal of the top console to remove a plafond of illumination of salon and the handle of opening of the hatch, to unscrew two screws of fastening of a forward part of the console, to lower a forward part of the console downwards and to shift back.
3. To remove a back cover of hours, preliminary having unscrewed two screws.
4. To unscrew two screws of fastening and to take hours.
5. To establish hours on the console.
6. To establish a back cover of hours and then the top console.

Removal and installation прикуривателя

PERFORMANCE ORDER
1. To remove a wire of weight from the accumulator.
Forward lighter
2. On models with the raised level of furnish of salon for access to прикуривателю to remove from a radio receiver an overlay of the central console.
3. On models with usual furnish of salon to remove a radio receiver.
4. To disconnect from прикуривателя wires and to take it from a highlighted ring.
Back lighter
5. To remove the handle of management of a heater.
6. To remove the panel of the back central console, preliminary having unscrewed two screws of fastening.
7. To disconnect from прикуривателя wires and to take it from a highlighted ring.
8. Installation is made in sequence, return to removal.

Removal and installation of a sound signal

In the car two sound signals are established. The sound signal of a high-pitch tone is established to the right of a radiator and is accessible from a motor compartment. The low-frequency sound signal is established from below and to the left of a radiator and is accessible from below a motor compartment.

PERFORMANCE ORDER
1. To unscrew a fixing nut or a bolt and to remove виброгасящую a washer.
2. To remove electric sockets and to take a sound signal.
3. Installation is made in sequence, return to removal.

Removal and installation of the switch of a sound signal, contact rings and brushes

PERFORMANCE ORDER
1. To remove a wire of weight from the accumulator.
2. Remove the central overlay of a steering wheel.
3. To unscrew three screws (are specified by arrows) fastenings скобы the switch of a sound signal.
4. To remove an electric socket and to take скобу the switch of a sound signal.
5. To remove a steering wheel.
6. To unbend ears of fastening of contact rings to the bottom part of a steering wheel, to disconnect from скобы and to remove contact rings.
7. To remove the top and bottom casings of a steering column.
8. To disconnect wires from brushes of a sound signal.
9. Being careful, to squeeze out the block of brushes a screw-driver inserted under a bottom edge of the block.
10. Installation is made in sequence, return to removal.

Removal and installation of elements of a heater of seats

PERFORMANCE ORDER
1. To remove a seat.
2. To remove a seat upholstery.
3. To note a direction of an arrangement of a heating element, then to remove wire clips and a sticky tape, крепящую an element to sitting.
4. To establish clips on a new element.
5. To establish a new heating element the forward party to pillow foam rubber. To fix a heating element wire clips and a tape. To check up that the heating element caves in at the appendix of loading to sitting.
6. To establish a sitting upholstery.
7. To establish sitting.
8. The regulator (arrow) should be directed the forward party to pillow foam rubber.

Removal and installation of contact group of the lock of ignition

PERFORMANCE ORDER
1. To remove a wire of weight from the accumulator.
2. To remove the top and bottom casings of a steering column, preliminary having unscrewed six screws of fastening.
3. To release contact group of the lock of ignition (arrow), having wrung out two fixing ears.
4. At installation to check up that the cut in the centre of contact group of the lock of ignition was made even to a ledge on the lock.
5. To connect contact group of the lock of ignition and to press it into place to защелкивания fixing ears.
6. To connect a weight wire to the accumulator and to check up working capacity of contact group of the lock of ignition, then to establish casings of a steering column.