dahlquist dq-20 review

FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   + 3.2. Engine DOHC
   - 3.3. Engine V6
      3.3.1. A technical characteristics
      3.3.2. The repair which is not demanding removal of the engine
      3.3.3. Engine removal
      + 3.3.4. Dismantling and check of details of the engine
      - 3.3.5. Changes in a design of engines V6 2,4 and 2,9 дм3
         3.3.5.1. Engine removal
         3.3.5.2. Heads of the block of cylinders
         3.3.5.3. Dismantling and assemblage of a head of the block of cylinders
         3.3.5.4. Replacement of a chain of a drive of the mechanism timing
         3.3.5.5. Adjustment of a backlash of valves
         3.3.5.6. The oil pump
   + 3.4. Ignition and engine management systems
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment



3.3.5.4. Replacement of a chain of a drive of the mechanism timing
THE GENERAL DATA

The top casing of a radiator, plastic скоба and a pin

Bolt of fastening of a suspension bracket of a pipe of system of cooling

Installation натяжителя chains

Clearing плунжера натяжителя chains

Fixing плунжера натяжителя chains

Bolt of the mechanism of a tension drive a generator belt

Bolt of the mechanism of a tension drive a belt of the pump of the amplifier of a steering


PERFORMANCE ORDER
1. Turning a cranked shaft for the central bolt of fastening гасителя крутильных fluctuations, to establish the piston of 1 cylinder in an ignition point (12 before ВМТ). Correctness of installation can be checked up, having uncovered the ignition distributor, thus the distributor rotor should be combined with contact of a high-voltage wire going to the cylinder number 1.
2. To remove a wire of weight from the accumulator.
3. To uncover the air filter together with the gauge of a stream of air and hoses.
4. To uncover маслозаливной mouths.
5. To merge cooling liquid from cooling system.
6. To disconnect a hose of connection of the water pump and a broad tank.
7. To remove the top casing of a radiator and a radiator.
8. To remove the fan from a nave of the water pump.

The prevention

The nut of fastening of the fan has the left carving.


9. To disconnect hoses of system of cooling from unions of the water pump.
10. To unscrew a bolt of fastening of a suspension bracket of a hose of system of cooling from a forward cover.
11. To remove auxiliary приводной a belt.
12. To unscrew 4 bolts and to remove a pulley of a cranked shaft.
13. To block a cranked shaft for a gear wreath of a flywheel, to unscrew the central bolt of fastening гасителя крутильных fluctuations and to remove it, using a special stripper.
14. To merge engine oil from the engine.
15. To disconnect wires, to unscrew and remove a starter.
16. Being careful, the load-lifting mechanism to raise the engine, and then to unscrew holders of the engine.
17. To check up that the steering wheel is established in movement position directly forward and a paint or a marker to note position of the bottom collar of an intermediate shaft and a gear wheel of steering transfer, then to disconnect an intermediate shaft from steering transfer.
18. To disconnect brake tubes from a beam of a forward suspension bracket.
19. To prop up a beam by means of the corresponding lift and a wide board.
20. To unscrew bolts of fastening of a beam to the car bottom. To incline a beam so that access to oil картеру was released.
21. To unscrew bolts and nuts of fastening oil картера and to take it from under the engine.
22. To unscrew 9 bolts of fastening of a cover of the mechanism timing and to uncover together with the water pump.
23. To check up that labels (are specified by arrows) on asterisks are directed to each other. Otherwise to tighten a cranked shaft before combination of labels.
24. To unscrew and remove натяжитель chains of a drive of the mechanism timing.
25. To fix an asterisk of a camshaft and to unscrew a bolt of fastening of an asterisk.
26. To remove a camshaft asterisk together with a chain and to remove a chain from an asterisk of a cranked shaft.
27. If necessary to remove from a cranked shaft an asterisk with шпонкой and directing to a chain.
28. Carefully to clear interfaced surfaces of traces of old linings.
29. To check up position шпоночных grooves on distributive and cranked shaft. They should be directed to each other.
30. To establish on a cranked shaft directing chains and an asterisk with шпонкой.
31. To establish a chain on an asterisk of a cranked shaft.
32. To establish a chain on an asterisk of a camshaft and to establish an asterisk together with a chain on a camshaft, thus шпонка a camshaft should enter into an asterisk groove.
33. To screw up a bolt of fastening of an asterisk of a camshaft.
34. To compress натяжитель chains for what to press плунжер натяжителя and to keep it in this condition, having adhered a corresponding tape.
35. To establish натяжитель chains into place, thus having removed a tape keeping плунжер.
36. To establish a lining of a forward cover of the mechanism timing.
37. To replace a sealing ring of a forward cover of the mechanism timing.
38. To establish a forward cover of the mechanism timing.
39. To centre an aperture in a cover concerning a cranked shaft, and also to level in relation to a plane of installation oil картера.
40. To screw bolts of fastening of a forward cover of the mechanism timing (are specified by arrows).
41. Carefully to clear interfaced surfaces of the block of cylinders and oil картера.
42. To establish a new lining in flutes oil картера.
43. To put hermetic on forward and back sites oil картера.
44. To put the structure interfering unscrewing on a carving of bolts, to establish oil картер and to screw up bolts.
45. To grease with engine oil working edges of a sealing ring and a surface interfaced to a ring гасителя крутильных fluctuations and to establish гаситель on a cranked shaft.
46. To screw up the central bolt of fastening гасителя крутильных fluctuations by the corresponding moment.
47. To establish a pulley of a cranked shaft.
48. To establish a beam and brake tubes.
49. To connect an intermediate shaft to steering transfer.
50. To establish a starter and to connect wires.
51. To establish auxiliary приводной a belt.
52. To establish the fan and a radiator.
53. To establish a cover of the air filter.
54. To fill in in the engine engine oil and cooling liquid in system of cooling of the engine.