FORD SCORPIO

1985-1994 of release

Repair and car operation



Ford Skorpio
+ 1.1. Car identification
+ 2. Maintenance service
- 3. Engines
   + 3.1. Engine OHC
   + 3.2. Engine DOHC
   - 3.3. Engine V6
      3.3.1. A technical characteristics
      3.3.2. The repair which is not demanding removal of the engine
      3.3.3. Engine removal
      - 3.3.4. Dismantling and check of details of the engine
         3.3.4.1. Engine dismantling
         3.3.4.2. Check of degree of deterioration of details of the engine
         3.3.4.3. Axis knot коромысел
         3.3.4.4. Pushers of valves and a bar of pushers
         3.3.4.5. A camshaft
         3.3.4.6. Heads of the block of cylinders
         3.3.4.7. Cylinders
         3.3.4.8. Check and restoration of pistons and piston rings
         3.3.4.9. Piston fingers and rods
         3.3.4.10. A cranked shaft
         3.3.4.11. Radical and шатунные bearings
         3.3.4.12. Distributive gear wheels
         3.3.4.13. A flywheel
         + 3.3.4.14. Greasing system
         3.3.4.15. Ventilation system картера
         + 3.3.4.16. Engine assemblage
         3.3.4.17. Adjustment of backlashes of valves
         3.3.4.18. Auxiliary details of the engine
         3.3.4.19. Engine installation
         3.3.4.20. Start of the engine after major repairs or restoration
      + 3.3.5. Changes in a design of engines V6 2,4 and 2,9 дм3
   + 3.4. Ignition and engine management systems
   + 3.5. Diesel engines
+ 4. Cooling system
+ 5. Fuel system
+ 6. Coupling
+ 7. Transmissions
+ 8. A kardannyj shaft and the back bridge
+ 9. A steering
+ 10. Suspension brackets
+ 11. Brake system
+ 12. Wheels and tyres
+ 13. A body
+ 14. An electric equipment


3.3.4.6. Heads of the block of cylinders
THE GENERAL DATA

The complete set inlet (above) and final valves


Consolidation inlet (at the left) and final valves


PERFORMANCE ORDER
1. To remove oil and a dirt from heads of the block of cylinders. To remove a deposit from chambers of combustion and heads of valves by means of a scraper or a rotating metal brush.
2. To compress клапанные springs by means of the corresponding adaptation for compression клапанных springs and to remove crackers of valves. To remove the adaptation for compression клапанных springs and to remove a plate клапанной springs, a spring and the valve. To mark each valve, subsequently to establish on a former place.
3. After removal of valves to remove a deposit from walls of channels.
4. To check up plates of valves and a saddle on presence выкрашивания and обгорания. Traces small выкрашивания on the valve and a valve saddle can be eliminated by grinding in at first coarse-grained, and then fine-grained шлифовочной paste. At scars выкрашивания valves are necessary for grinding on the machine tool for grinding of valves, and a saddle on the machine tool for фрезеровки saddles of valves. It is necessary to address for performance of two last kinds of works to experts.
5. To check up directing valves on deterioration presence: to insert the valve in directing, the valve in the directing should move easily, without a lateral backlash. Special tools are necessary for replacement worn out directing on new, therefore it is necessary to address to experts.
6. Grinding in of valves is necessary for making with application only fine-grained polishing paste.
7. A surface of a saddle of the valve to grease with a small amount of paste and to establish the valve in a corresponding saddle. Densely to press to a valve plate a rubber sucker and to rotate the valve in one or other party.
8. After the termination of process of grinding in all details carefully to clear of a dirt and paste and to check up a saddle and a valve plate. The continuous matte ring on both details which specifies width of a facet of the valve should be visible.
9. To check up клапанные springs on effort of compression and length of springs without loading.
10. To grease a core of the valve with engine oil and to establish in directing the valve. To establish new consolidation.
11. To establish клапанную a spring and a plate клапанной springs.
12. By means of the corresponding adaptation for compression клапанных springs to compress a spring so that crackers were established in grooves in a valve core. To remove the adaptation.
13. After installation of all details into place, slightly to knock with a hammer with plastic brisk from above клапанных springs to be convinced that crackers were established into place.